PCFL-180P-X2S2 / UPS function / Industrial PC PSUs / Products / Bicker Elektronik

PCFL-180P-X2S2

150 Watt

UPS function with NiMH battery pack
No minimum load required
Special voltages possible

The ATX power supply PCFL-180P-X2S2 uniquely combines the functions of a PC power supply with those of a UPS. Energy is provided by a separate NiMH battery pack in a practical 3.5“ format. Upon request it is also available with additional 24 V DC output voltage. A UPS software monitors the supplied system so that operation without user supervision is possible. A fit-form-compatible variation of the PCFL-180P-X2S2 is available with DC input as well.

Technical data
Input voltage	85…264 VAC, active PFC
Input frequency	47…63 Hz
Input current	2 A (100 VAC) / 0.9 A (220 VAC)
Efficiency	77 % typ.
Hold up time	16 msec (without battery pack)
Power-Good-Signal	Switch on delay 100…500 msec Switch off delay 1 msec
Protection	Short circuit protection: At each output, switch off, +5 Vsb auto-recovery, at input: fuse Overvoltage protection: +3.3 V (3.7…4.3 V), +5 V (5.7…6.7 V), 12 V (13.8…15.6 V), +5 Vsb (5.7…7 V)
Insulation voltage	Input / Chassis: 1500 VAC for 60 sec. Input / Output: 1500 VAC for 60 sec.
Safety / EMC	CE, EN 60950-1, UL 60950-1
Operating temperature	0…+60 °C
Derating	85…90 V, 80 % load +30…+60 °C 2% / °C fanless, 1.3 % / °C with fan
MTBF	100 000 h
Storage temperature	-20…+70 °C
Operating humidity	10…95 % RH, non-condensing
Dimensions (WxDxH)	93 x 160 x 55 mm ±0.4 mm
Weight (net)	0.85 kg

Product-specific data

Vibration	10…55 Hz with 2 G, duration 10 cycles, per x, y, z axis (out of operation)
UPS function	By connection of battery pack BS17A-H24/2.0L

Article No.	Output voltage	Output current max	Heat sink max	Fan max	Peak 5 sec.	Load regulation	Ripple & Noise
PCFL-180P-X2S2	+3.3 V	10 A	10 A	10 A	10 A	±5 %	50 mV
	+5 V	10 A	10 A	10 A	10 A	±5 %	50 mV
	+12 V	7.5 A	8.5 A	10 A	15 A	±5 %	120 mV
	-12 V	0.3 A	0.3 A	0.3 A	0.3 A	±10 %	120 mV
	+5 Vsb	1 A	1 A	1.5 A	1.8 A	±5 %	50 mV

Max. output power is 90 W without fan, 100 W with heat sink (>1.6 K/W) and 150 W with fan cooling (30 m3/h). Combined output load at +3.3 and +5 V must not exceed 60 W in fanless operation, it must not exceed 70 W for operation with heat sink, and with fan cooling (30 m3/h) it must not exceed 83 W. Ripple and noise was measured by a 20 MHz bandwidth limited oscilloscope with connected 47 µF ceramic capacitor at each output.
This power supply is for assembly purposes only and it must not be operated in unassembled condition. The final assembly has to comply with the valid EMC standards.