BEP-506
80 Watt
- 60 Watt continuous fanless power!
- Operating temperature 0…+70 °C
- Also with DC input and for medical uses available
By its extremely compact design the BEP-506 was especially developed for low-power ATX and ITX mainboards of Intel, AMD, and VIA. It is the ideal power supply for fanless working applications. Without active cooling the BEP-506 supplies an output power of 60 W, which can even be increased to 80 W with fan. It is designed for an ambient temperature range of 0 up to +70 °C. For easy connection an ATX cable harness is available by default. Typical uses for the BEP-506 are personal servers, POS, POI and IPCs.
| Technical data |
|
|---|---|
| Input voltage |
90…264 VAC, 127…373 VDC |
| Input frequency |
47…63 Hz |
| Input current |
2 A (115 VAC) / 1 A (230 VAC) |
| Inrush current |
30 A (115 VAC) / 60 A (230 VAC) |
| Efficiency |
>73 %, 230 VAC at full load |
| Hold up time |
20 msec, 230 VAC |
| Power-Good-Signal |
Switch on delay 100…500 msec |
| Protection |
Short circuit protection: at each output, auto-recovery |
| Earth leakage current |
<3,5 mA |
| Safety / EMC |
CE, TÜV: EN60950-1, UL60950-1 |
| Operating temperature |
0…+70 °C |
| Derating |
2.5 % / K from +50…+70 °C |
| MTBF |
162 000 h (60 W) at 25 °C according to MIL-HDBK-217F |
| Storage temperature |
-20…+70 °C |
| Operating humidity |
5…95 % RH, non-condensing |
| Dimensions |
128 x 81 x 40 mm ±0.5 mm |
| Weight (net) |
0.25 kg |
|
Article |
Output |
Output current |
Output current |
Voltage |
Ripple & |
|---|---|---|---|---|---|
| BEP-506 |
+3.3 V |
0 A |
6 A |
±4 % |
50 mV |
| +5 V |
1 A |
8 A |
±3 % |
50 mV |
|
| +12 V |
0 A |
3 A |
±4 % |
120 mV |
|
| -12 V |
0 A |
0.5 A |
±5 % |
120 mV |
|
| +5 Vsb |
0 A |
0.75 A |
±4 % |
120 mV |
Output power is 60 W without fan and 80 W with an 8.6 CFM fan (15 m3/h). Combined output load at +3.3 V and +5 V must not exceed 40 W. Under full load at both the +5 V and +3.3 output (approx. 40 W) a minimum load of +12 V / 0.2 A must be connected. Ripple and Noise was measured by a 20 MHz bandwidth limited oscilloscope with connected 10 µF electrolytic capacitor and 0.1 µF ceramic capacitor at each output.
As a power component this PSU is for assembly purposes only and must not be operated in unassembled condition. The final assembly has to comply with the valid EMC and safety standards.
The power supply does provide no circuit for power factor correction (PFC). Thus, according protective measures are required from a power consumption of >75 W.
| Optional accessories | ||
Article-No. |
Designation |
|
|---|---|---|
| CB-506 | ATX cable harness for BEP-506 | link to the product |
| X1-024 | AC input cable harness / 2 poles / Length: 620 mm / AWG 18 / Ends open | link to the product |
