BEP-515C
150 Watt
- +24 VDC input
- 150 Watt continuous fanless power!
- Operating temperature up to +70 °C
By its rugged design and widerange input from 18 VDC to 36 VDC the 150 W ATX power supply BEP-515C is the ideal power supply for fanless working applications used in automation or mobile systems. Full power can be supplied at an ambient temperature of +50 °C. For easy connection an ATX cable harness is available. Fit-form-function compatible power supplies with AC-Input or for medical use are available as BEP-515 and BEP-515M.
| Technical data |
|
|---|---|
| Input voltage |
18…36 VDC |
| Input current |
15 A max. |
| Inrush current |
18 A max. |
| Efficiency |
≥75 % (at nominal power and +24 VDC) |
| Hold up time |
>5 ms (at nominal load and +24 VDC) |
| Power-Good-Signal |
Switch on delay 100…500 ms |
| Protection |
Short circuit protection: At each output, switch off (-12 V), auto-recovery |
| Insulation voltage |
Input / Chassis 1866 VDC |
| Safety / EMC |
UL, CE |
| Operating temperature |
0…+70 °C |
| Derating |
+50…+70 °C, 2.5 % / °C |
| MTBF |
130 000 h at +50 °C according to MIL-217F |
| Storage temperature |
-20…+70 °C |
| Operating humidity |
5…95 % RH, non-condensing |
| Dimensions (W x D x H) |
97 x 198 x 40 mm ±0.4 mm |
| Weight (net) |
0.7 kg |
|
Article |
Output |
Output current |
Output current |
Output current |
Load |
Line |
Ripple & |
|---|---|---|---|---|---|---|---|
| BEP-515C |
+3.3 V |
0 A |
12 A |
7.5 A |
±4 % |
±1 % at rated load |
50 mV |
| +5 V |
1 A |
14 A |
11 A |
±2 % |
50 mV |
||
| +12 V |
0 A |
10 A |
5 A |
±4 % |
100 mV |
||
| -12 V |
0 A |
1.0 A |
0.5 A |
±5 % |
150 mV |
||
| +5 Vsb |
0 A |
1.5 A |
0.75 A |
±4 % |
100 mV |
Combined output load at +3.3 V and +5 V must not exceed 90 W. The +5 V output can supply up to 14 A if a minimum load of +3.3 V / 0.2 A and +12 V / 2 A is connected. The +3.3 V output can supply 12 A if a minimum load of +5 V / 2 A and +12 V / 0.2 A is connected. Ripple and Noise was measured by a 20 MHz bandwidth limited oscilloscope with connected 10 µF electrolytic capacitor and 0.1 µF ceramic capacitor at each output. Load regulation was done by changing the measured output load ±40 % from 60 % rated load and all other outputs kept at 60 % rated load.
As a power component this PSU is for assembly purposes only and must not be operated in unassembled condition. The final assembly has to comply with the valid EMC and safety standards.
| Optional accessories | ||
Article-No. |
Designation |
|
|---|---|---|
| CB-515 | ATX cable harness for BEP-515 | link to the product |
