PCFL-180P-X2S2
150 Watt
- UPS function with NiMH battery pack
- No minimum load required
- Special voltages possible
The ATX power supply PCFL-180P-X2S2 uniquely combines the functions of a PC power supply with those of a UPS. Energy is provided by a separate NiMH battery pack in a practical 3.5“ format. Upon request it is also available with additional 24 V DC output voltage. A UPS software monitors the supplied system so that operation without user supervision is possible. A fit-form-compatible variation of the PCFL-180P-X2S2 is available with DC input as well.
| Technical data |
|
|---|---|
| Input voltage |
85…264 VAC, active PFC |
| Input frequency |
47…63 Hz |
| Input current |
2 A (100 VAC) / 0.9 A (220 VAC) |
| Efficiency |
77 % typ. |
| Hold up time |
16 msec (without battery pack) |
| Power-Good-Signal |
Switch on delay 100…500 msec |
| Protection |
Short circuit protection: At each output, switch off, +5 Vsb auto-recovery, at input: fuse |
| Insulation voltage |
Input / Chassis: 1500 VAC for 60 sec. |
| Safety / EMC |
CE, EN 60950-1, UL 60950-1 |
| Operating temperature |
0…+60 °C |
| Derating |
85…90 V, 80 % load +30…+60 °C 2% / °C fanless, 1.3 % / °C with fan |
| MTBF |
100 000 h |
| Storage temperature |
-20…+70 °C |
| Operating humidity |
10…95 % RH, non-condensing |
| Dimensions (WxDxH) |
93 x 160 x 55 mm ±0.4 mm |
| Weight (net) |
0.85 kg |
| Product-specific data |
|---|
| Vibration |
10…55 Hz with 2 G, duration 10 cycles, per x, y, z axis (out of operation) |
| UPS function |
By connection of battery pack BS17A-H24/2.0L |
|
Article |
Output |
Output current |
Output current |
Heat sink |
Fan |
Peak |
Load |
Ripple & |
|---|---|---|---|---|---|---|---|---|
| PCFL-180P-X2S2 |
+3.3 V |
0 A |
10 A |
10 A |
10 A |
10 A |
±5 % |
50 mV |
| +5 V |
0 A |
10 A |
10 A |
10 A |
10 A |
±5 % |
50 mV |
|
| +12 V |
0 A |
7.5 A |
8.5 A |
10 A |
15 A |
±5 % |
120 mV |
|
| -12 V |
0 A |
0.3 A |
0.3 A |
0.3 A |
0.3 A |
±10 % |
120 mV |
|
| +5 Vsb |
0 A |
1 A |
1 A |
1.5 A |
1.8 A |
±5 % |
50 mV |
Max. output power is 90 W without fan, 100 W with heat sink (>1.6 K/W) and 150 W with fan cooling (30 m3/h). Combined output load at +3.3 and +5 V must not exceed 60 W in fanless operation, it must not exceed 70 W for operation with heat sink, and with fan cooling (30 m3/h) it must not exceed 83 W. Ripple and noise was measured by a 20 MHz bandwidth limited oscilloscope with connected 47 µF ceramic capacitor at each output.
This power supply is for assembly purposes only and it must not be operated in unassembled condition. The final assembly has to comply with the valid EMC standards.
| Optional accessories | ||
Article-No. |
Designation |
|
|---|---|---|
| BS17A/H24/2.0L | NiMH battery pack, 24 V/2,0 Ah | link to the product |
| RUPS 2000-B1 | UPS Management Software (CD-ROM) | link to the product |
| WH-M2022-500-01 | PCFD/L-180P / 20 pin ATX connector / 500 mm | link to the product |
| WH-PS610-850 | 3x HD / 2x SATA / 1x FDD cable harness / 850 mm | link to the product |
| CB-PCFL | AC input cable for PCFL-180P | link to the product |




